Pocket Hole Jig Station. DIY. Cheap and Simple

16,933

260

14

Introduction: Pocket Hole Jig Station. DIY. Cheap and Simple

Hello!

Today i will show you how to make quick and easy Pocket Hole Jig Station. Pocket holes are one of many methods of joining wood together. It uses the simplest of joinery- right angle cuts mostly, and relies on the mechanical strength of screws to hold an assembly together. Although glue is sometimes used to augment it, the screws themselves do most of the work.

Step 1:

Original kreg jigs are very expensive. My project will allow you to save lots of money and you can spend them for some other tools. Besides the jig can be dismounted and used freely about the workpiece.

Step 2:

Step 3:

Lets start! I took an oak Board and mark center. Then i cut two pieces of board. I will use them as a support for pocket hole jig. I used jig and drilled holes in this supports. Add some glue and fixed with screws.

Step 4:

If you do everything right, then you will get flat surface with right angle.

Step 5:

Now I will make a mount for the vacuum cleaner. I cut two pieces of board 8*8 cm and add one more pieces between them. The vacuum cleaner pipe is attached very tightly.

Step 6:

Now we shuld make a fixing clamp. I take F Clamp and replace one pice (as shown on the picture)

Step 7:

Now we need to fix this clamp to the base. I cut two pieces of wood and drilled holes in it. Fixed with screws.

Step 8:

Thats it, we all done! Our Pocket Hole Jig System is ready and we a redy to try it in work. Thanks to this clamp we can fixed wood with different width. Vacuum dust remover work perfect.

Step 9:

I spend about $ 15 on this project, but it works just as well as the $150 original jig.

I hope you like it! Thanks for watching and have a nice day!

Build a Tool Contest

Participated in the
Build a Tool Contest

1 Person Made This Project!

Recommendations

  • Anything Goes Contest

    Anything Goes Contest

14 Comments

0
luiessir
luiessir

4 months ago

¡Qué buenísima idea, gracias por compartirla Polkilo!
¡Internet es una hermosa herramienta!

0
jeneli41
jeneli41

2 years ago on Step 9

the link to clamp is for the wrong size clamp it would be helpfull if you specifyed the size clamp you used. Nice projject.

0
Luc Therrien
Luc Therrien

Question 2 years ago on Introduction

Can I use something other than oak (3/4 inch ply for example) to make it less expensive)? Do you have specific dimensions for the project?

0
Polkilo
Polkilo

Answer 2 years ago

you can also use plywood. I just had some scraps of oak wood left. you can choose any size. I designed a compact station, you can make a large one. if you need specific dimensions, I can measure my station

0
Luc Therrien
Luc Therrien

Reply 2 years ago

Dimensions would be great. I prefer working off somewhat of a plan. A bit of a newbie to woodworking.

0
MatthewM425
MatthewM425

2 years ago on Step 3

This is a good idea and I can see how it could be incorporated into a work bench for larger material.

1
Marcos1970
Marcos1970

2 years ago

Top 16 !
Great great idea !

0
Polkilo
Polkilo

Reply 2 years ago

Thank you so much 👍😊

0
Ralphxyz
Ralphxyz

2 years ago

Thank you!! I absolutely hate my Kreg Jig Master.

Ralph

0
Polkilo
Polkilo

Reply 2 years ago

You are welcome:)

3
garfieldgurl
garfieldgurl

2 years ago

What a great tool! Thank you for sharing!

0
Polkilo
Polkilo

Reply 2 years ago

Thank you so much 👍