Finishing a 3D Print

933

20

4

Introduction: Finishing a 3D Print

Achieve a silky smooth finish on your 3d Prints! I’ll be using a mask I made as an example, though this method is applicable to most 3D prints as long as they aren’t too small or detailed since finer details will most likely be lost in the process.

Supplies

● A 3D print, preferably in PLA or another softer plastic but it will work with other materials (Make sure it has thick walls to allow for sanding)

● Various grits of sandpaper from rough to fine.

● A can of filler primer, I used Rustoleum brand (you don’t need the sandable kind)

● Paint, spray paint for the best surface finish

Step 1: Sanding

Since sanding plastic is harder than sanding filler primer, you don’t have to get the part perfectly smooth now, just get rid of the worst of the ridges from the printing process. Starting with your roughest grit sandpaper, sand in an elliptical pattern against the direction of the ridges. Once you get it as smooth as possible, move up to a higher grit. Repeat the process until your part is nice and smooth or you get sick of sanding. You can see in the picture that my part was still fairly rough when I moved on to the next step, but I was still able to achieve a very smooth finish.

Step 2: Filling

Take that can of filler primer I told you to buy and absolutely hose your part down with it. They tell you to apply light coats, but that’s a lie. Just completely cake that stuff on. The purpose of filler primer is to fill imperfections and by golly we’re going to do just that.

Once the primer is dry, get a bucket of water or just hold your part under a sink and wet sand the primer back down to the surface of the part. Having a continuous flow of water either form a faucet or dunking in a bucket makes the primer really easy to sand. Use a medium grit sandpaper and very carefully sand down the primer, since the primer is so soft it’s very easy to accidentally remove it from the grooves and flaws you were trying to fill in.

Step 3: Priming

Prime your part for real for this time. Since this is the final coat of primer, we want the highest quality finish on it that we can manage. You can either use the same filler primer from earlier or regular primer, but either way, actually follow the instructions on the side of the can about applying multiple light coats. When the primer is dry, lightly wet sand it once more with a high grit sandpaper to achieve the smoothest possible finish.

Step 4: Painting

Make it look real pretty. To avoid brush strokes, I recommend using spray paint; apply several light coats letting the paint at least partially dry in between to prevent the paint from pooling up and causing drips.

Be the First to Share

    Recommendations

    • CNC and 3D Printing Contest

      CNC and 3D Printing Contest
    • Puzzles Challenge

      Puzzles Challenge
    • Rice & Grains Challenge

      Rice & Grains Challenge

    4 Comments

    0
    Invents_Studio
    Invents_Studio

    Tip 2 years ago on Step 4

    ●If you don’t have spray paint, an oil-based paint will show brush strokes less than other types of paint

    ●For and even smoother finish, lightly sand the undercoats of paint with a very high grit
    sandpaper

    ●If you’re doing something more colorful, it’s good to apply a base coat of white paint first for a more vibrant final color.

    0
    Invents_Studio
    Invents_Studio

    Tip 2 years ago on Step 3

    Be careful not to sand too much, you don’t want to expose the part under the primer.

    0
    Invents_Studio
    Invents_Studio

    Tip 2 years ago on Step 2

    ●If you did a better job sanding or have a smaller part you can be less liberal when applying the prime. The goal is for the primer to be thicker than the deepest flaw in
    the part.

    ●This is when you’ll lose fine details since the primer can’t distinguish between fine
    features that are and aren’t supposed to be there.

    0
    Invents_Studio
    Invents_Studio

    Tip 2 years ago on Step 1

    If your part is already pretty high quality coming off the printer, start with a higher grit
    sandpaper. If the sandpaper is rougher than the part you’ll end up making it
    less smooth!