Easy Guide to REPAIR Broken BOSE QC25 Headphones - NO SOUND From One Ear




Introduction: Easy Guide to REPAIR Broken BOSE QC25 Headphones - NO SOUND From One Ear

Bose is well known for their headphones, and more especially their active noise cancelling lineup. The first time I put a pair of QuietComfort 35's on in an electronics store, I was blown away by the silence they can create. However, I had a very little budget I wanted to spend on another pair of headphones that I would use only occasionally when travelling. So I began looking for Bose headphones on second-hand websites. I found a pair of QC25's that had a broken right side speaker and bought them from the auction for only 15€. The problem of blown speakers seems to be a common problem with the QC25's. So, here's a tutorial on how to fix your broken pair of headphones saving money and the planet by the way!

Ps: Here's a video I made on the project for lazy people who don't have time to read the article:


A pair of broken QC25 (or QC35) headphones

A replacement driver: Amazon - https://amzn.to/2QTAL3o Ebay-


A Soldering Iron

A Hair Dryer

A Small Phillips Head Screwdriver


Step 1: Gain Access to the Electronics

First, you need to remove the earpads as well as the felt covers to gain access to the screws holding down the metal covers of the headphones.

Removing the earpads is very easy - you just have to pull them under a slight angle and the plastic tabs holding the pads in place will pop out.

There are two screws for each cover. Put them somewhere safe, as you'll need them later!

Note: Of course, before beginning the teardown, make sure that the problem comes indeed from the headphones and not the cable (by trying a different cable or by doing a continuity test of the cable using a multimeter).

Step 2: Diagnosing the Speakers

To make sure that the problem comes indeed from the speakers and not the motherboard, you can measure their resistance by placing the probes of your multimeter set to ohmmeter mode on the terminals of the speakers (shown with a red arrow on the first picture). The polarity doesn't matter when doing the measurement.

A working speaker should have a resistance of around 32Ω.

However, a broken speaker has a resistiviry a lot higher than that: in my case, it was 2.04 kΩ.

If both speakers are fine, the problem comes from the motherboard - to find a replacement, the easiest way is to buy another pair of broken QC25's that have the opposite side broken. The working motherboard could then be salvaged and transplanted on the initial pair.

Step 3: Removing the Faulty Speaker

The covers on the speakers are solidly glued on. To remove them, you first need to remove the two screws holding the cover in place. Then, you can use a hair dryer to slowly soften the glue. After a minute, you can try to pull it away using a flat head screwdriver as a crowbar. Be careful not to damage the cover in the process, as you will have to glue it back on later.

DO NOT use a hot air gun to soften the glue. I did that on the first pair I tore down and the heat was too intense for the plastic - it made it shrink as you can see on the fifth image. Even if you keep the air gun far from the cover, it is too aggressive and difficult to control. Using a hair dryer is a lot safer and easier, as you can put it right next to the targeted area and the plastic won't shrink.

To remove the speaker, use the same strategy: hairdryer + gentle pulling with a screwdriver.

Step 4: Installing the New Speaker

If you managed to get to this step, congratulations! The difficult part is now over and the remaining steps are fairly easy:

First, get hold of a replacement speaker. You can salvage it from another pair of Bose headphones if you have a collection of them, or you can buy a clone from the web.

The sound quality won't match the original perfectly, but with the noise cancellation on the sound is already a bit distorted (making it difficult to tell the difference between the original and the copy). Sometimes you can also find legit replacements on eBay.

Installing the speaker is easy: just glue it in place and solder the wires back on.

Then, glue the plastic cover back on.

Finally, put the metal covers and the earpads back and you're done!

Step 5: Done!

Congratulations! You have now a working pair of noise QuietComfort 25's! By fixing the old pair you did not only save money but also helped keep our planet clean and fight against overconsumption!

I hope you learned something new along the journey.

If you liked this instructable please consider voting for me in the ''Fix it'' contest.

Thank you for reading and have a great day!

Fix It Contest

Participated in the
Fix It Contest

Be the First to Share


    • Lamps Challenge

      Lamps Challenge
    • Rice & Grains Challenge

      Rice & Grains Challenge
    • CNC and 3D Printing Contest

      CNC and 3D Printing Contest



    Answer 11 months ago

    ¡Hola! ¿Quizás comprar otro auricular roto en eBay? ¿O modelar la pieza en 3D si tiene acceso a una impresora 3D?


    Question 1 year ago on Step 5

    Hi great instructions. Speaker fitted but I have a whistling sound as soon as I switch on the noise canceling


    1 year ago

    So nice to have these headphones working again. Bose no longer supports
    these under warranty and would only allow you to buy new ones at a
    slight discount, which still would be around $200. I tried other
    tutorials using paper to try to press the driver in a certain location
    to make it work again but that barely solves anything. I am so happy
    that you figured out what was wrong with these and made this tutorial it
    was well done and thorough.

    Not sure what glue you used to
    re-attach the driver and cover, but I used foaming gorilla glue and it
    worked well to re-seal everything (only stuff I had on hand). The noise cancelling is back to working like new.

    Also, if you happened to
    know what type of wire they used for connecting the driver to the
    motherboard that would be great - I accidentally shortened mine and was
    barely able to get it to reach. May have to replace it in the future if
    the driver craps out again.


    2 years ago

    Very comprehensive 'ible! I recently bought a set of reconditioned Bose QC35II's off the internet, and when I received them, the on-off switch was very hard to use, to the point that I eventually broke it. When I complained to the vendor, he refunded my money, so now I had a broken set of Bose QC35II's free of charge. I bought a replacement switch on ebay for $7.95 for 25 switches, and after an easy modification to the switch to make it compatible, replaced the bad one, and now have a perfectly good set of Bose QC35II noise cancelling headphones with great bass and bluetooth. They look and act like brand new ones, and even came with the cables, and cost me a total of $7.95, versus $349 for new ones!


    Reply 2 years ago

    I'm still happy with my QC25's but I'll admit, a free pair of Bluetooth QC35's sounds like a great hustle! :D

    Alex in NZ
    Alex in NZ

    2 years ago

    Great job, and very comprehensively documented as well. Thank you for sharing your work, and well done on the repair :-)


    Reply 2 years ago

    Thank you Alex! :D