DIY Arduino Based Auto Label Dispenser Machine

10,658

83

16

Introduction: DIY Arduino Based Auto Label Dispenser Machine

About: Electrical engineer by profession

Hello makers in this video I have made a arduino based auto label dispenser machine, this machine dispense labels automatically.

When you are in packaging and transporting industry there are continue parcel which need to label some sticker, this machine very much helpful there.

It automatically peel off label and dispense this make process fast. For this I used arduino micro controller, stepper motor to feed label roll and IR sensor to detect label

JLCPB is best PCB manufacturer they have very resonable PCB pricing and fast PCB production
You can surely consider JLPCB for your any PCB needs $2/5pcs 2Layer & $5/5pcs 4Layer PCBs: https://jlcpcb.com

Step 1: VIDEO

You can watch this complete video how I made this cool amazing fully automatic label dispenser machine

Step 2: Components Required

  1. Custom PCB
  2. Motor Clamp
  3. Arduino Nano
  4. A4988 driver IC
  5. Nema 17 stepper motor
  6. 5mm ID timing pully
  7. 8mm pillow bearing
  8. 8mm & 5mm smooth SS shaft 200mm
  9. 8mm ID timing pully
  10. Timing belt
  11. Push button
  12. Rotary Knob
  13. 16X2 I2C LCD display
  14. 3D printed parts
  15. IR Sensor

All 3D files you can download it from here

https://www.thingiverse.com/thing:4631473

Step 3: CIRUIT DRAWING

Here the gerber file of the PCB I used in this project also attached the simple circuit drawing so that you can make it if you don't want PCB

Step 4: CONSTRUCTION

As you watched in video

Most of the part of this machine is made up of 12mm wooden sheet

There are mainly three wooden parts are Left, right and bottom part.

I mark the necessary dimensions on the wooden sheet and cut them with the help of my mini table saw

Then I placed the electrical parts and nema 17 stepper motor in between of two vertical wooden parts

I have used to 8MM shaft one to hold the label roll and one to pull the roll which is directly connected to the stepper motor,

Some 5 mm smooth rods are for slide guide for label

one IR sensor at the bottom continually detect the presence of label if label is not present it command stepper motor to run.

Some 3D printed parts are also used in this project like top cover of machine.

One 16X2 LCD is used for data display and some knob and push button is used for user data input.

hope you like this project if you have any comment please write it down below.

Be the First to Share

    Recommendations

    • CNC and 3D Printing Contest

      CNC and 3D Printing Contest
    • Rice & Grains Challenge

      Rice & Grains Challenge
    • Lamps Challenge

      Lamps Challenge

    16 Comments

    0
    jnnjnn
    jnnjnn

    Question 7 months ago on Introduction

    Hi! Would you like to help me? I need more information about parameters of some components used in this project to buy the right ones. I will be grateful for your response!

    0
    Ochi5857
    Ochi5857

    10 months ago

    The code am really a learner need help

    1
    Ochi5857
    Ochi5857

    Question 10 months ago on Introduction

    What's the code it's really useless with out the code

    0
    sahyunid1
    sahyunid1

    Question 1 year ago

    please Can you tell me the code ?? ToT

    0
    sahyunid1
    sahyunid1

    Question 1 year ago on Step 3

    당신은 나에게 코드를 말할 수 있습니까?

    0
    randofo
    randofo

    Answer 1 year ago

    (FYI: They are asking for the code)

    0
    sahyunid1
    sahyunid1

    Reply 1 year ago

    please Can you tell me the code ?? ToT

    0
    Georg_SR
    Georg_SR

    1 year ago

    Hello, I had the circuit boards sent to me and assembled, but during commissioning the output stages get very hot and break.Can you help me there and is there an electronics planthanks

    0
    Abdullah Noushad
    Abdullah Noushad

    2 years ago

    I think that the code is there in his video

    0
    andre1jr
    andre1jr

    2 years ago

    Will you please post the arduino code?

    THANKS!

    0
    Lacybad
    Lacybad

    2 years ago

    What can i say? A really genuine idea and i think it can be adapted to similar ones. Absolutely great job :)